PREMIUM PYE PV200 S40H

Name: PREMIUM PYE PV200 S40H
Brand: NEXLER
SKU: W-PAM05-W1D2A-NX1R-0600

Heat weldable top layer bituminous felt

Application:

Top layer bituminous felt in multilayer roofing
Restoration of old bituminous felt coverings
Multi-layer roofing with a slope of min. 1%

Properties:

Flexible and durable reinforcement resistant to high temperatures
Double SBS modification
Approved for use in reduced ambient temperatures

Available packaging:

6 m, 8 m

Type of reinforcement	non-woven polyester reinforced with glass fibers
Top finishing	coarse grained
Low temperature flexibility	≤ -20°C
Width	≥ 0,99 m
Straightforwardness	≤ 12 mm per 6 m of roll length ≤ 16 mm per 8 m of roll length
Resistance to external fire exposure* *applies to the examined layer systems	B_roof(t₁), B_roof(t₂), B_roof(t₃)
Reaction to fire	class E
Watertightness: waterproof at a pressure	≥ 10 kPa (method A) ≥ 250 kPa (method B)
Maximum tensile force: - longitudinal extension - transversal extension	850 ± 250 N/50 mm (50 ± 15) % 600 ± 200 N/50 mm (50 ± 15) %
Resistance to root penetration	NPD
Durability: flow resistance at elevated temperature	(100 ± 10)°C
Dimensional stability	≤ 0,5%
Reference document(s)	EN 13707:2004+A2:2009

Making an insulation using NEXLER PREMIUM PYE PV200 S40H bituminous felt should be carried out according to the technical design, in accordance with the current building regulations and the detailed guidelines for the design and execution of insulation contained in NEXLER Insulation Systems and the Technical Data Sheet.
The bituminous felt should be installed in ambient temperatures of above 0°C, this requirement applies to the time of day and night.
Do not carry out insulation work during strong winds and precipitation.
The substrate should meet the following requirements:
- dry substrate (no visible traces of moisture or darkening caused by moisture),
- clean substrate (the surface is free of dust, oil stains, grease and other contaminants),
- smooth substrate (local unevenness and cavities in the surface of concrete do not exceed ± 5 mm),
- even substrate (the gaps between the surface of the substrate and a 4 m long patch placed on the concrete substrate do not exceed 10 mm),
- roof slope inclination min. 1%.
Before welding NEXLER PREMIUM PYE PV200 S40H bituminous felt it is recommended to prime old bitumen layers with water-based bitumen products for example NEXLER BITFLEX Primer, or solvent-based bitumen primers for example NEXLER Penetrator G7.
NEXLER PREMIUM PYE PV200 S40H bituminous felt should be welded to the previously installed underlayer bituminous felt or to the primed old bituminous felt covering. Application should be carried out after the priming agent has completely dried (or cured).
As a result of heating both the substrate and the underside of the bituminous felt with a burner, the thin protective plastic foil melts, the asphalt is slightly melted and the bituminous felt sticks evenly to the substrate. Maintain a bituminous felt overlap min. 8 cm wide along the length of the felt strip and an overlap min. 12 cm wide at the joint perpendicular to the length of the felt strip. Overlaps of the bituminous felt at joints perpendicular to the length of the bituminous felt on adjacent sheets should be offset from each other by at least 50 cm. An asphalt outflow of approx. 0,5 - 1 cm in width over the entire length of the welded overlap is required.
Before use, please read the application details in the product's Technical Data Sheet.